Just How to Install a Bathtub Yourself
Just How to Install a Bathtub Yourself
Blog Article
We have noticed this great article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the web and accepted it made perfect sense to discuss it with you on this page.
Setting up a bathtub isn't specifically brain surgery, yet it does require strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old tub with a new one is additionally a reasonably difficult task. If the old tub is readily obtainable, the project can relocate rapidly; if you have to open up a wall to get rid of the old bathtub and place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and embeded in the new one. Make certain you have certified yourself for the task as well as are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed project, it is far better to think about employing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This short article will certainly assist you mount a new bath tub in your shower room if you have actually already gotten a new tub and also don't need to transform the arrangement of your previous water system pipelines.
Your tools as well as product checklist ought to consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. When the supply pipes have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making sure that the washers are in place in between the faucet as well as the sink. Protect the tap in position with the supplier supplied backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical faucet ports. The former kind ought to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the level and also adjusting the feet on the bath tub until the level reviews level.
To mount taps, fit all-time low of the furthest versatile faucet port to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water as well as examine all joints and new pipework for leakages and tighten them if needed. Load the bathtub as well as additionally check the overflow electrical outlet and also the normal outlet for leakages.
Finally, repair the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bathtub ought to wait till the bath tub has been utilized at the very least once as this will settle it right into its last position.
Getting ready for the Setup
To start with, the supporting frame supplied with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its last setting.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to break a rigid seal, causing the water to pass through the wall surface between the bath and also the tiling, bring about issues with moisture and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealer can crack rather early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently offered on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Write feedback directly below. We would be glad to find out your responses about this piece. We hope to see you back again in the near future. Do you know another individual who is interested in How to Install a Bathtub Yourself? Why not share it. Thank you for your time. Come back soon.
This Page
Report this page